Strobon SE v2 - Navigation Strobe Controller

Strobon SE v2 is completely same circuit design with our revolutionary STROBON v2 Navigation Strobes excluding the LED and size.  It is more flexible than other LED embedded Strobon models. 
Now, it's configurable for 5 different patterns.
Strobe/Blink/Heartbeat/Rotating Beacon/Solid

More details

£3.55

ProductFrom (qty)Discount
Strobon SE v2 - Navigation Strobe Controller25 -£1.05
Strobon SE v2 - Navigation Strobe Controller10 -£0.80
Strobon SE v2 - Navigation Strobe Controller5 -£0.55

STROBON Lights are the most powerful navigation lights on the model market since years.

Strobon SE v2 is completely same circuit design with our revolutionary STROBON v2 Navigation Strobes excluding the LED and size. It is a more flexible design than other LED embedded Strobon models. 

Now, it's configurable for 5 different patterns!

  1. Strobe  (Legendary Strobon v1 strobe effect. 3 fast flashes like xenon wing tip flashlights)
  2. Blink (Simulates belly or tail lights. Continuous ON/OFF)
  3. Heartbeat (standard beacon light pattern, ramp up/ramp down/off)
  4. Rotating Beacon (perfect simulation of rolling beacons. ramp up/flash/ramp down/off)
  5. Static (you can use it as landing headlights or static wing-tip lights)

It allows 2 different working modes;

  • RC Controlled Mode: Plug it on your RC receiver’s any channel for RC mode, then you can enable/disable it over selected servo channel. 
    Each Strobon counts the servo signals. So, you can plug more than one Strobon to the same RC channel to synchronize them.  (check the schematic below)

  • Standalone Mode: Power it with directly from the battery (3.5-6v) it works on Standalone mode and works continuously.

It works with any Power LED(3W)  and it also drives more than one Power LED (the colours must be the same for same forward voltage).

You can order Sotrobon SE compatible high-quality 3W Power LEDs from our store

http://www.flytron.com/12-rc-light-systems 

SCHEMATIC for SYNCRONIZED & RC CONTROLLED MODE

Strbon SE v2 RC Controlled Light Cabling

    RC CHANNEL SETTINGS

    

SCHEMATIC for STAND ALONE MODE

Strobon SE v2 Standalone Cabling

PATTERN SELECTION

All you need a piece of wire or a tweezer to change the pattern. 
Connect two small pads of the Strobon SE v2 board while it's working (it will not change the pattern when it's OFF)
It will stop working when you connect these pins and jump to next pattern when you release the connection. 
That's all.

Strobon SE v2 Cabling and Pattern Selection

Airplane Navigation Light Locations

Customer Video, Thank you Fernando :)
(you can find the instructions and wiring details under the video description)

  

Customer Video (thank you Otto)

In this video, we soldered two Power LED back to back for 360 degrees visible strobe. 

Specifications 

  • Supply Voltage: 3.5 - 6 volt
  • Current Consumption per hour  @5V
    Strobe: average 60mA (1A in event of the flash)
    Blink: 70mA (150ma ON)
    Heartbeat: 120mA
    Rolling Beacon: average  170mA (1A in event of the flash)
    Static: 140mA
  • 24.3mm X 9.2mm X 2mm
  • Weight: 0.3 gram without wires
  • Operating Temperature: -40 to +105 °C

 

Frequently Question: How many LEDs can it drives?
Answer: There is no limit. The light intensity drops depend led count. Our suggestion is maximum 3-5 units 3W Power LEDs gives acceptable light intensity. 

Related Products